Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57061

The friction angle represents_______________________?

Select your answer for: The friction angle represents_______________________?
Show answer

Answer: A. angle between normal reaction and the resultant of normal reaction and the limiting friction

Explanation

The friction angle is the angle between the normal reaction force and the resultant vector of normal and limiting friction. This angle provides a convenient geometric measure of the coefficient of static friction between two contact surfaces. As surface roughness increases the limiting friction grows larger causing the friction angle to increase accordingly. Friction forces resist the relative lateral motion of solid surfaces sliding against each other. Normal reaction is the component of contact force perpendicular to the shared surface plane. Limiting friction represents the maximum possible static friction force before sliding motion commences.

Mechanical engineers use the friction angle to determine self-locking conditions in wedge and screw mechanisms. Geotechnical engineers apply friction angle concepts to analyze soil stability and slope failure risks. Tribology research studies surface interactions to minimize friction angles and reduce mechanical energy losses. Option B defines the coefficient of static friction rather than the geometric friction angle itself. Option C and D incorrectly describe ratios of minimum friction forces instead of vector resultants. Option E confuses the friction angle with empirical ratios comparing static and dynamic friction coefficients.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. The center of gravity for a solid conical mass is located along its axis at a height of_____________________?

Select your answer for: The center of gravity for a solid conical mass is located along its axis at a height of_____________________?
Show answer

Answer: A. one-fourth of the total height above base

The center of gravity of a solid right circular cone sits at one fourth of its total height. This vertical position is measured upward directly from the flat circular base of the cone. Integration of mass distribution ac...

Q2. The principle of transmissibility states that the mechanical action of a force on a rigid body_________________?

Select your answer for: The principle of transmissibility states that the mechanical action of a force on a rigid body_________________?
Show answer

Answer: C. the same at every point in its line of action

The principle of transmissibility applies strictly to rigid body mechanical analysis. Sliding a force vector along its exact line of action leaves external effects unchanged. Internal stresses may alter, but external rig...

Q3. The center of gravity for a thin hollow conical shell lies along its axis at what fractional height___________________?

Select your answer for: The center of gravity for a thin hollow conical shell lies along its axis at what fractional height___________________?
Show answer

Answer: B. one-third of the total height above base

The center of gravity for a thin hollow conical shell lies along its axis at one-third of the total height above the base. Integrating the elemental surface areas of a hollow cone yields a centroid located closer to the...

Q4. For dry sliding surfaces, frictional resistance is________________?

Select your answer for: For dry sliding surfaces, frictional resistance is________________?
Show answer

Answer: C. proportional to velocity of sliding

Kinetic frictional resistance for dry sliding surfaces remains proportional to velocity over standard ranges. Frictional force behavior changes with sliding speed depending on lubrication and surface roughness properties...

Q5. An overhead trolley wire has a mass of 1.2 kg per meter. Its ends are secured to poles spaced 20 meters apart. Given a horizontal tension load of 1500 kg, calculate the center sag (dip) of the span___________________?

Select your answer for: An overhead trolley wire has a mass of 1.2 kg per meter. Its ends are secured to poles spaced 20 meters apart. Given a horizontal tension load of 1500 kg, calculate the center sag (dip) of the span___________________?
Show answer

Answer: C. 4.0 cm

Cable sag formulas calculate center dip using distributed weight and span tension. Multiplying mass per meter by span squared and dividing by eight times tension gives sag. Substituting one point two kg per meter and fif...

Q6. D’Alembert’s principle is applied to convert dynamic problems into equivalent problems of______________________?

Select your answer for: D’Alembert’s principle is applied to convert dynamic problems into equivalent problems of______________________?
Show answer

Answer: A. reducing the problem of kinetics to equivalent statics problem

D'Alembert's principle introduces an inertia force, transforming a dynamic problem of kinetics into an equivalent static equilibrium problem. By applying a fictitious inertia force equal to mass times acceleration, dynam...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test