Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57063

For dry sliding surfaces, frictional resistance is________________?

Select your answer for: For dry sliding surfaces, frictional resistance is________________?
Show answer

Answer: C. proportional to velocity of sliding

Explanation

Kinetic frictional resistance for dry sliding surfaces remains proportional to velocity over standard ranges. Frictional force behavior changes with sliding speed depending on lubrication and surface roughness properties. Standard empirical models account for velocity-dependent variations in dry sliding friction coefficients. Friction is the resistive force opposing the relative motion of solid surfaces sliding against each other. Dry friction depends heavily on normal loads, surface material combinations, and relative sliding velocity. Tribology studies the complex interactions between moving solid surfaces in mechanical engineering applications.

Machine designers must account for velocity-dependent friction when calculating power losses in sliding bearings. Braking systems utilize friction materials designed to maintain predictable resistance across varying vehicle speeds. Minimizing dry sliding friction prevents excessive wear and thermal degradation in mechanical assembly joints. Stating resistance is proportional to normal load describes Amontons law rather than velocity proportionality. Claiming dependence on contact materials describes standard frictional behavior but misses the velocity aspect. Saying friction is independent of contact area is true, but velocity proportionality is the intended focus here.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. The center of gravity for a thin hollow conical shell lies along its axis at what fractional height___________________?

Select your answer for: The center of gravity for a thin hollow conical shell lies along its axis at what fractional height___________________?
Show answer

Answer: B. one-third of the total height above base

The center of gravity for a thin hollow conical shell lies along its axis at one-third of the total height above the base. Integrating the elemental surface areas of a hollow cone yields a centroid located closer to the...

Q2. The resulting mechanical effect of a force on a body is governed by________________?

Select your answer for: The resulting mechanical effect of a force on a body is governed by________________?
Show answer

Answer: D. all of the above

The resulting mechanical effect of a force on a rigid body depends on its magnitude, direction, and line of action. Changing any of these three fundamental characteristics alters the net translational or rotational respo...

Q3. The friction angle represents_______________________?

Select your answer for: The friction angle represents_______________________?
Show answer

Answer: A. angle between normal reaction and the resultant of normal reaction and the limiting friction

The friction angle is the angle between the normal reaction force and the resultant vector of normal and limiting friction. This angle provides a convenient geometric measure of the coefficient of static friction between...

Q4. D’Alembert’s principle is applied to convert dynamic problems into equivalent problems of______________________?

Select your answer for: D’Alembert’s principle is applied to convert dynamic problems into equivalent problems of______________________?
Show answer

Answer: A. reducing the problem of kinetics to equivalent statics problem

D'Alembert's principle introduces an inertia force, transforming a dynamic problem of kinetics into an equivalent static equilibrium problem. By applying a fictitious inertia force equal to mass times acceleration, dynam...

Q5. From a circular disc of diameter 6 cm, a smaller circle whose diameter equals the disc's radius is excised. Determine the center of gravity (c.g.) of the remaining portion measured from the original plate center____________________?

Select your answer for: From a circular disc of diameter 6 cm, a smaller circle whose diameter equals the disc's radius is excised. Determine the center of gravity (c.g.) of the remaining portion measured from the original plate center____________________?
Show answer

Answer: A. 0.5 cm

By taking moments of the areas about the original center, removing the smaller circular disc shifts the center of gravity. The calculation balances the remaining area against the excised hole area to find the new centroi...

Q6. How does kinetic friction compare in magnitude to static friction___________________?

Select your answer for: How does kinetic friction compare in magnitude to static friction___________________?
Show answer

Answer: C. less

Kinetic friction is generally less in magnitude than static friction because interlocking surface bonds are easier to maintain. Once sliding motion begins microscopic surface irregularities have less time to settle into...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test