Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57510

Large forgings, crankshafts, and axles typically contain carbon up to________________?

Select your answer for: Large forgings, crankshafts, and axles typically contain carbon up to________________?
Show answer

Answer: C. 0.45 to 0.55%

Explanation

Medium carbon steels used for heavy forgings contain carbon ranging from 0.45 to 0.55 percent. This specific carbon concentration provides a favorable balance of high tensile strength and toughness. Heat treatment processes can successfully harden this carbon range for demanding mechanical loads. Carbon content is the primary factor determining the mechanical properties of plain carbon steel. Crankshafts and axles endure severe cyclic bending and torsional stresses during regular operation. Forging refines the internal grain structure of steel to improve fatigue resistance and strength.

Automotive and locomotive drive shafts rely on medium-carbon steel for long-term structural reliability. Heavy industrial machinery components require careful material selection to prevent catastrophic fatigue failure. Machinists must use appropriate cutting tools when shaping components made from medium carbon steel. Lower carbon ranges between 0.05 and 0.20 percent are typical for soft, ductile structural steels. Ranges from 0.20 to 0.45 percent provide moderate strength for general structural parts and bolts. Higher carbon ranges above 0.55 percent are generally reserved for hard tools and springs.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. While highly efficient, isothermal compression is impractical because_________________?

Select your answer for: While highly efficient, isothermal compression is impractical because_________________?
Show answer

Answer: D. compressor has to run at very slow speed to achieve it

Isothermal compression requires gas temperature to remain constant by continuously removing heat during the process. Rapid compression generates heat quickly, meaning effective heat rejection requires massive surface are...

Q2. Kinematic viscosity is formulated as_________________?

Select your answer for: Kinematic viscosity is formulated as_________________?
Show answer

Answer: A. dynamic viscosity/density

Kinematic viscosity relates dynamic fluid friction directly to the inertial mass density of the fluid. Mathematical formulation defines kinematic viscosity as dynamic viscosity divided by fluid density. This ratio simpli...

Q3. Inconel is categorized as an alloy of___________________?

Select your answer for: Inconel is categorized as an alloy of___________________?
Show answer

Answer: A. nickel, chromium and iron

Inconel is categorized as an alloy of nickel, chromium, and iron. Metallurgical compositions of superalloys include high percentages of nickel. Adding chromium and iron provides exceptional resistance to oxidation and co...

Q4. At atmospheric pressure, dry steam latent heat equals____________________?

Select your answer for: At atmospheric pressure, dry steam latent heat equals____________________?
Show answer

Answer: A. 539 kcal/kg

Latent heat of vaporization represents the thermal energy required to convert liquid water into steam at constant pressure. Experimental thermodynamic measurements establish that water requires approximately 539 kilocalo...

Q5. Accelerated-circulation boilers feature________________?

Select your answer for: Accelerated-circulation boilers feature________________?
Show answer

Answer: B. water is supplied in drum and through downcomers” located in atmospheric conditon it passes to the water wall and rises to durm in the from of mixture of water and steam

Accelerated-circulation boilers utilize density differences between fluid columns to promote rapid water movement. Water is supplied from steam drums through external downcomers to heated water wall tubes. Heat conversio...

Q6. How does blow-by past piston rings and valve seats in internal combustion engines vary with speed_______________?

Select your answer for: How does blow-by past piston rings and valve seats in internal combustion engines vary with speed_______________?
Show answer

Answer: B. decreases

Higher engine speeds reduce the available time window for gas leakage to occur. Less blow-by volume escapes past piston rings and valve seats during rapid engine cycles. The duration of high pressure exposure per combust...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test