Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57133

Fire tube boilers are restricted to a top design working pressure of ____________________?

Select your answer for: Fire tube boilers are restricted to a top design working pressure of ____________________?
Show answer

Answer: C. 17 kg/cm2

Explanation

Fire tube boilers are generally limited to lower working pressures typically up to seventeen kilograms per square centimeter. The large outer cylindrical shell of a fire tube boiler must contain high-pressure steam over a wide diameter. Structural stress limits prevent fire tube boilers from safely operating at the extreme pressures used in power plants. Fire tube boilers pass hot combustion gases through internal tubes surrounded by the water vessel. Water tube boilers route water inside smaller high-pressure tubes surrounded by combustion gases instead. Boiler design pressure dictates the thickness of metal plating required to prevent catastrophic pressure vessel failure.

Fire tube boilers are widely used in low-pressure industrial heating and smaller steam processing applications. Power generation plants exclusively use water tube boilers to achieve pressures exceeding one hundred kilograms per square centimeter. Safety regulations mandate periodic hydrostatic pressure testing for all industrial steam boilers. Option A and B specify working pressure limits that are much too low for standard industrial fire tube boilers. Option D and E represent high-pressure thresholds that require water tube boiler architecture to operate safely. others_commentary_note_filler_not_present

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. Fire tube boilers are characterized by__________________?

Select your answer for: Fire tube boilers are characterized by__________________?
Show answer

Answer: A. flue gases pass through tubes and water around it

In fire tube boilers, hot flue gases pass through the inside of the tubes while water surrounds them. This configuration houses the water and steam within a large outer shell enclosing the internal gas tubes. Heat transf...

Q2. The center of percussion is defined as___________________?

Select your answer for: The center of percussion is defined as___________________?
Show answer

Answer: C. the point of application of the resultant of all the forces tending to cause a body to rotate about a certain axis

The center of percussion marks the exact point where resultant forces cause pure rotation. Hitting this specific location on a suspended body produces no reactive shock at the pivot. Mathematical derivations define it us...

Q3. Water flow through a pipe roughly 3 meters across is measured using__________________?

Select your answer for: Water flow through a pipe roughly 3 meters across is measured using__________________?
Show answer

Answer: D. pitot tube

A pitot tube is commonly used to measure fluid velocity and flow rates in large pipes, such as those approximately 3 meters across. Large-diameter conduits prevent the use of standard inline flow meters, making insertion...

Q4. These specific elements feature a face-centered cubic lattice__________________?

Select your answer for: These specific elements feature a face-centered cubic lattice__________________?
Show answer

Answer: A. gamma iron (910° to 1400°C), Cu, Ag, Au, Al, Ni, Pb, Pt

Gamma iron and numerous ductile non-ferrous metals crystallize into face-centered cubic lattices. This specific atomic arrangement features atoms located at each corner and cube face center. Face-centered cubic structure...

Q5. For a body floating in a fluid, the normal pressure exerted by the liquid acts upon____________________?

Select your answer for: For a body floating in a fluid, the normal pressure exerted by the liquid acts upon____________________?
Show answer

Answer: D. all points on the surface of the body

Normal pressure exerted by a fluid on a submerged or floating body acts perpendicularly to all points in contact along the entire surface. Fluid pressure has no directional component parallel to a frictionless surface, c...

Q6. Forces that intersect at a single point but whose lines of action do not share a common plane are termed_________________?

Select your answer for: Forces that intersect at a single point but whose lines of action do not share a common plane are termed_________________?
Show answer

Answer: B. non-coplanar concurrent forces

Concurrent forces intersect at a single common point within their geometric coordinate system layout. When their lines of action do not occupy the same two-dimensional plane, they are classified as non-coplanar. Combinin...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test