Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57136

For a body floating in a fluid, the normal pressure exerted by the liquid acts upon____________________?

Select your answer for: For a body floating in a fluid, the normal pressure exerted by the liquid acts upon____________________?
Show answer

Answer: D. all points on the surface of the body

Explanation

Normal pressure exerted by a fluid on a submerged or floating body acts perpendicularly to all points in contact along the entire surface. Fluid pressure has no directional component parallel to a frictionless surface, creating purely normal forces everywhere. Integrating these distributed normal pressure forces over the wetted area yields the total buoyant force vector. Fluid statics dictates that static pressure acts equally in all directions and always impinges perpendicularly on boundaries. Archimedes' principle relies on this pressure distribution to explain why submerged objects experience upward buoyancy. Depth-dependent hydrostatic pressure increases linearly from the waterline down to the deepest submerged points.

Limiting normal pressure to the bottom surface ignores the substantial lateral and upward pressures acting on hull sides. Center of gravity is a mass property point and does not represent a physical surface where fluid pressures act. The metacentre is a geometric point used for stability analysis rather than a physical surface subject to fluid pressure.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. For a system of forces to remain in equilibrium, it is necessary that they be_________________?

Select your answer for: For a system of forces to remain in equilibrium, it is necessary that they be_________________?
Show answer

Answer: C. both A. and B. above

Static equilibrium requires that the vector sum of all forces and the sum of all moments equal zero. For a force system to satisfy these equilibrium conditions, the forces must act within the same plane. Additionally, th...

Q2. Fire tube boilers are restricted to a top design working pressure of ____________________?

Select your answer for: Fire tube boilers are restricted to a top design working pressure of ____________________?
Show answer

Answer: C. 17 kg/cm2

Fire tube boilers are generally limited to lower working pressures typically up to seventeen kilograms per square centimeter. The large outer cylindrical shell of a fire tube boiler must contain high-pressure steam over...

Q3. Select the statement that is incorrect_________________?

Select your answer for: Select the statement that is incorrect_________________?
Show answer

Answer: D. the sine of the angle of repose is equal to coefficient to friction

The tangent of the angle of repose equals the friction coefficient, making the sine statement incorrect. Trigonometric analysis of inclined planes shows that the coefficient of friction equals tangent theta. Stating that...

Q4. Maintaining identical power and speed, how does a four-stroke engine flywheel compare in size to a two-stroke I.C. engine flywheel________________?

Select your answer for: Maintaining identical power and speed, how does a four-stroke engine flywheel compare in size to a two-stroke I.C. engine flywheel________________?
Show answer

Answer: B. bigger

A four-stroke engine fires once every two crankshaft revolutions requiring a bigger flywheel to maintain uniform speed. The extended non-firing power strokes in a four-stroke engine create larger speed fluctuations durin...

Q5. Given equal tube diameter and wall thickness, a water-tube boiler relative to a fire-tube boiler features____________________?

Select your answer for: Given equal tube diameter and wall thickness, a water-tube boiler relative to a fire-tube boiler features____________________?
Show answer

Answer: A. more heating surface

Water-tube boilers route water inside smaller diameter tubes with hot gases flowing externally around them. This arrangement provides a much larger cumulative heat transfer surface area compared to fire-tube designs of e...

Q6. What are the units for mass moment of inertia ________________?

Select your answer for: What are the units for mass moment of inertia ________________?
Show answer

Answer: A. kg m2

Mass moment of inertia is the product of mass and squared distance, yielding units of kg meters squared. Multiplying kilograms by meters squared results from integrating mass elements over radial distance paths. Dimensio...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test