Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57504

Isothermal compression efficiency, even at high speeds, is approached through A. multi-stage compression B. cold water spray C. both A. and B. above D. fully insulating the cylinder E. high stroke_________________?

Select your answer for: Isothermal compression efficiency, even at high speeds, is approached through A. multi-stage compression B. cold water spray C. both A. and B. above D. fully insulating the cylinder E. high stroke_________________?
Show answer

Answer: C. both A. and B. above

Explanation

Multi-stage compression with intercooling removes heat between stages to keep temperatures low. Cold water sprays injected into the cylinder absorb heat directly during the compression process. Both methods limit temperature rises, helping the compression process approach isothermal conditions. Isothermal compression occurs at a constant temperature, minimizing the total work required. Adiabatic compression generates rapid heat, requiring significantly more mechanical input power. Thermodynamic efficiency improves when gas compression temperatures are kept as low as possible.

Large industrial air compressors utilize multi-stage intercooled systems to save operational energy. Pneumatic tool networks depend on efficiently cooled compressed air to prevent moisture accumulation. Power plant gas turbines use multi-stage compression to optimize overall cycle thermal efficiency. Multi-stage compression alone helps, but water sprays also actively contribute to cooling the air. Cold water spray alone lowers temperatures, but multi-stage compression is equally standard practice. Fully insulating the cylinder traps heat, causing adiabatic conditions and increasing compression work.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. Air preheater design must primarily account for the consideration that_________________?

Select your answer for: Air preheater design must primarily account for the consideration that_________________?
Show answer

Answer: D. stack gases should not be cooled to the dew point

Flue gases contain sulfur dioxide and water vapor that combine to form corrosive sulfuric acid at low temperatures. Cooling the exhaust gases below their acid dew point causes liquid acid to condense on metallic duct sur...

Q2. Perpetual inventory control checks materials as stock levels reach their__________________?

Select your answer for: Perpetual inventory control checks materials as stock levels reach their__________________?
Show answer

Answer: A. minimum value

Perpetual inventory control systems monitor stock levels continuously as materials are issued or received. When inventory quantities drop down to the established minimum threshold, automated reorder triggers activate. Th...

Q3. Which boiler is recommended for generating large steam volumes at low pressure?

Select your answer for: Which boiler is recommended for generating large steam volumes at low pressure?
Show answer

Answer: C. lancashire boiler

Lancashire boilers generate large steam volumes at relatively low pressures. Their large shell capacity holds significant water volume for steady operations. Internal fire tubes provide adequate heating surface for indus...

Q4. While highly efficient, isothermal compression is impractical because_________________?

Select your answer for: While highly efficient, isothermal compression is impractical because_________________?
Show answer

Answer: D. compressor has to run at very slow speed to achieve it

Isothermal compression requires gas temperature to remain constant by continuously removing heat during the process. Rapid compression generates heat quickly, meaning effective heat rejection requires massive surface are...

Q5. Kinematic viscosity is formulated as_________________?

Select your answer for: Kinematic viscosity is formulated as_________________?
Show answer

Answer: A. dynamic viscosity/density

Kinematic viscosity relates dynamic fluid friction directly to the inertial mass density of the fluid. Mathematical formulation defines kinematic viscosity as dynamic viscosity divided by fluid density. This ratio simpli...

Q6. Inconel is categorized as an alloy of___________________?

Select your answer for: Inconel is categorized as an alloy of___________________?
Show answer

Answer: A. nickel, chromium and iron

Inconel is categorized as an alloy of nickel, chromium, and iron. Metallurgical compositions of superalloys include high percentages of nickel. Adding chromium and iron provides exceptional resistance to oxidation and co...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test