Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57400

Diesel engine knock is primarily caused by____________________?

Select your answer for: Diesel engine knock is primarily caused by____________________?
Show answer

Answer: A. instantaneous and rapid burning of the first part of the charge

Explanation

Diesel knock is caused by rapid auto-ignition of accumulated fuel built up during the ignition delay. A large mass of fuel injected during the delay period burns almost instantaneously, causing sharp pressure spikes. This abrupt pressure shockwave creates the characteristic audible knocking sound in diesel engines. Ignition delay is the time interval between fuel injection and the start of actual combustion. High combustion chamber pressure rates of rise stress engine mechanical components during knock events. Cetane number and intake air temperature strongly influence the duration of the ignition delay period.

Diesel engine calibration aims to minimize ignition delay to prevent harsh combustion noise and vibration. Using high cetane number diesel fuels helps reduce knocking by promoting prompt and smooth auto-ignition. Diagnostic testing of knocking engines often points to faulty fuel injectors or low compression pressures. Option B is incorrect because knock originates from the rapid burning of the accumulated initial fuel charge. Option C is incorrect because delayed burning would reduce pressure spikes rather than cause sharp knocking. Option D is incorrect because reducing the delay period actually eliminates diesel knock rather than causing it.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. Wood possesses an average calorific value of approximately : __________?

Select your answer for: Wood possesses an average calorific value of approximately : __________?
Show answer

Answer: D. 19700 kj/kg

Wood possesses an average calorific value of approximately 19,700 kilojoules per kilogram. This energy density reflects the cellulosic composition of dry timber biomass fuels. Moisture content in green wood significantly...

Q2. In a typical medium-speed 4-stroke cycle diesel engine, how does the inlet valve operate_____________________?

Select your answer for: In a typical medium-speed 4-stroke cycle diesel engine, how does the inlet valve operate_____________________?
Show answer

Answer: A. opens at 20° before top dead center and closes at 35° after the bottom dead center

Advanced valve timing opens the inlet valve before top dead center to utilize incoming inertial momentum. Keeping the inlet valve open past bottom dead center captures additional incoming air due to high piston speeds. T...

Q3. Scavenging air in diesel engines refers to___________________?

Select your answer for: Scavenging air in diesel engines refers to___________________?
Show answer

Answer: D. air used for forcing burnt gases out of engine’s cylinder during the exhaust period

Scavenging air forces burnt exhaust gases completely out of the cylinder during the exhaust phase. It prepares the combustion chamber to receive a fresh charge of clean air for the next cycle. Option D correctly describe...

Q4. Gaseous fuel calorific values are quantified in terms of__________________?

Select your answer for: Gaseous fuel calorific values are quantified in terms of__________________?
Show answer

Answer: D. kcal/m²

Gaseous fuel calorific values are typically quantified per unit volume, such as kilocalories per cubic meter. Measuring gas volume is far more practical in engineering applications than weighing compressible gas masses....

Q5. What volume of air is needed to burn 1 liter of fuel in a four-stroke engine_______________?

Select your answer for: What volume of air is needed to burn 1 liter of fuel in a four-stroke engine_______________?
Show answer

Answer: D. 9-10 m3

Stoichiometric calculations dictate that hydrocarbon liquid fuels require massive volumetric quantities of atmospheric oxygen. Burning one single liter of typical fuel oil demands roughly nine to ten cubic meters of air....

Q6. Indicated mean effective pressure derived from an engine indicator represents________________?

Select your answer for: Indicated mean effective pressure derived from an engine indicator represents________________?
Show answer

Answer: E. average pressure

Indicated mean effective pressure represents the theoretical average pressure acting on the piston. Multiplying this average pressure by displacement gives the total indicated work per power stroke. Option E correctly de...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test