Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57041

A heavy ladder supported on a floor against a vertical wall may lose equilibrium if____________________?

Select your answer for: A heavy ladder supported on a floor against a vertical wall may lose equilibrium if____________________?
Show answer

Answer: C. the floor and wall both are smooth surfaces

Explanation

If both the floor and the wall are perfectly smooth, no frictional forces can exist to oppose sliding, causing the ladder to lose equilibrium and slip. Static equilibrium requires balancing horizontal and vertical forces as well as net rotational moments about any point. Smooth surfaces cannot provide tangential reaction forces, leaving the ladder with unbalanced forces that cause immediate movement. Friction forces act parallel to contact surfaces and are proportional to the normal reaction force between bodies. A ladder leaning against a wall relies on floor friction and wall friction or normal reactions to remain stable. According to the laws of static equilibrium, the sum of all external forces and moments acting on the ladder must equal zero.

A smooth wall combined with a rough floor still allows equilibrium because the floor friction can balance horizontal loads. A smooth floor and rough wall combination can maintain equilibrium if the wall friction provides the necessary upward support. Stating that the ladder remains in equilibrium under all conditions ignores the fundamental principles of static friction.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. Thermal cycle efficiency is elevated by________________?

Select your answer for: Thermal cycle efficiency is elevated by________________?
Show answer

Answer: C. both A. and B.

Both steam regeneration and reheating improve the overall thermal efficiency of steam power cycles. Regeneration preheats boiler feed water using extracted steam to reduce external heat addition requirements. Reheating s...

Q2. What are the fundamental dimensional units of surface tension___________________?

Select your answer for: What are the fundamental dimensional units of surface tension___________________?
Show answer

Answer: A. MlL°T2

Surface tension is defined mathematically as force acting per unit length along the surface of a liquid. Force has dimensional units of mass multiplied by acceleration, expressed as M L T^-2 in fundamental dimensions. Di...

Q3. During a polytropic thermodynamic expansion or compression_________________?

Select your answer for: During a polytropic thermodynamic expansion or compression_________________?
Show answer

Answer: D. all of the above

Polytropic processes involve simultaneous heat transfer, mechanical work, and property state changes in gases. Working fluids can shift between wet, dry, or superheated states during polytropic expansion or compression....

Q4. A projectile launched at an angle 9 relative to the vertical achieves its maximum horizontal range when 9 equals_______________?

Select your answer for: A projectile launched at an angle 9 relative to the vertical achieves its maximum horizontal range when 9 equals_______________?
Show answer

Answer: C. 45°

For a projectile launched from level ground maximum horizontal range is achieved at a launch angle of forty-five degrees. This optimal angle balances the initial vertical velocity component needed for flight time with ho...

Q5. Duralumin alloy composition consists of___________________?

Select your answer for: Duralumin alloy composition consists of___________________?
Show answer

Answer: A. 94% aluminium, 4% copper and 0.5% Mn, Mg, Si and Fe

Duralumin is a prominent precipitation-hardenable aluminum alloy containing approximately ninety-four percent aluminum. Four percent copper is added as the primary alloying element to enable significant strength enhancem...

Q6. A body starts from rest with a constant acceleration of 5 m/s². What is the approximate distance travelled in 5 seconds_________________?

Select your answer for: A body starts from rest with a constant acceleration of 5 m/s². What is the approximate distance travelled in 5 seconds_________________?
Show answer

Answer: B. 62.5 m

Using the kinematic formula s equals zero point five multiplied by acceleration and time squared. Multiplying zero point five by an acceleration of five and twenty five for time squared. Calculating this algebraic produc...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test