Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 56959

Peak compression ratios for single-stage axial flow compressors in practice typically reach orders of________________?

Select your answer for: Peak compression ratios for single-stage axial flow compressors in practice typically reach orders of________________?
Show answer

Answer: A. 1 : 1.2

Explanation

Axial flow compressor blades have strict aerodynamic turning limitations per stage. Excessive pressure gradients across a single stage induce flow separation and stall. Single-stage axial pressure ratios are therefore kept very low around 1.1 to 1.2. Compressor staging requires chaining multiple blade rows to achieve high total pressures. Boundary layer separation causes surge conditions that can destroy compressor blades. Euler's turbine equation governs the energy transfer limits per blade row.

Industrial and aviation gas turbines use multi-stage compressors with dozens of rows. Achieving high overall pressure ratios requires complex multi-spool engine architectures. Compressor design balances stage count against weight and mechanical complexity. A ratio of one to one represents zero pressure rise across the compressor stage. Higher single-stage ratios like one to five are only possible with centrifugal designs. Ratios of one to ten require multi-stage compression rather than single stages.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. Net work input required by a compressor responds to increases in cylinder clearance volume by_____________________?

Select your answer for: Net work input required by a compressor responds to increases in cylinder clearance volume by_____________________?
Show answer

Answer: C. remains same

The net work input per cycle for a reciprocating compressor depends on suction and discharge pressures. Clearence volume traps high-pressure gas that expands during the return stroke, re-expanding to suction pressure. Th...

Q2. The primary objective of implementing gas turbine reheating is to__________________?

Select your answer for: The primary objective of implementing gas turbine reheating is to__________________?
Show answer

Answer: C. increase power output

Reheating gas between turbine stages increases the specific power output of the gas turbine system. Injecting additional thermal energy expands the working fluid further and boosts overall turbine work production. This p...

Q3. The maximum temperature zone within a gas turbine plant is located at______________________?

Select your answer for: The maximum temperature zone within a gas turbine plant is located at______________________?
Show answer

Answer: D. between ~ to i of the blade height

Thermal and mechanical stress concentrations on gas turbine blades peak slightly inward from the tip region. The combination of centrifugal stress and hot combustion gas flow creates maximum temperature zones between mid...

Q4. Ideal thermal efficiency of a simple gas turbine cycle is a function of________________?

Select your answer for: Ideal thermal efficiency of a simple gas turbine cycle is a function of________________?
Show answer

Answer: A. pressure ratio

The ideal thermal efficiency of a simple Brayton gas turbine cycle is a function of pressure ratio. Higher pressure ratios expand the temperature limits across the ideal thermodynamic cycle loop. Thermodynamic equations...

Q5. How does the pressure ratio of an ideal vaned compressor respond to increases in mass flow rate_________________?

Select your answer for: How does the pressure ratio of an ideal vaned compressor respond to increases in mass flow rate_________________?
Show answer

Answer: C. remains constant

For an ideal compressor operating at a fixed speed the pressure ratio remains relatively constant over mass flow. Changes in mass flow rate do not alter the inherent pressure building capacity of an ideal rotating compre...

Q6. Surging instabilities in centrifugal compressor systems depend upon___________________?

Select your answer for: Surging instabilities in centrifugal compressor systems depend upon___________________?
Show answer

Answer: D. stagnation pressure at the outlet

Surge in centrifugal compressors is an unstable aerodynamic phenomenon triggered by mismatched outlet stagnation pressures. When system downstream pressure exceeds compressor delivery pressure capability, reverse flow oc...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test