Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57047

Constantan, an alloy widely used in thermoelectric sensors, consists of a combination of__________________?

Select your answer for: Constantan, an alloy widely used in thermoelectric sensors, consists of a combination of__________________?
Show answer

Answer: D. copper and nickel

Explanation

Constantan is a copper-nickel alloy characterized by a low coefficient of thermal expansion and stable electrical resistance. Combining copper and nickel in specific proportions creates a solid solution alloy with unique electrical and thermal properties. The alloy maintains a nearly constant electrical resistivity across a wide range of varying ambient temperatures. Constantan typically consists of roughly fifty-five percent copper and forty-five percent nickel by chemical weight composition. Electrical resistance alloys must exhibit high thermal stability to ensure accurate measurements in precision instrumentation. The material also has a high thermoelectric electromotive force when paired with metals like copper or iron.

Copper and tin combinations form traditional bronzes used for structural bearings, gears, and decorative architectural castings. Copper and zinc mixtures produce standard brass alloys used in plumbing fixtures and decorative hardware applications. Copper and iron combinations do not form standard constantan wire and lack the required electrical resistance stability.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. A projectile launched at an angle 9 relative to the vertical achieves its maximum horizontal range when 9 equals_______________?

Select your answer for: A projectile launched at an angle 9 relative to the vertical achieves its maximum horizontal range when 9 equals_______________?
Show answer

Answer: C. 45°

For a projectile launched from level ground maximum horizontal range is achieved at a launch angle of forty-five degrees. This optimal angle balances the initial vertical velocity component needed for flight time with ho...

Q2. Duralumin alloy composition consists of___________________?

Select your answer for: Duralumin alloy composition consists of___________________?
Show answer

Answer: A. 94% aluminium, 4% copper and 0.5% Mn, Mg, Si and Fe

Duralumin is a prominent precipitation-hardenable aluminum alloy containing approximately ninety-four percent aluminum. Four percent copper is added as the primary alloying element to enable significant strength enhancem...

Q3. A body starts from rest with a constant acceleration of 5 m/s². What is the approximate distance travelled in 5 seconds_________________?

Select your answer for: A body starts from rest with a constant acceleration of 5 m/s². What is the approximate distance travelled in 5 seconds_________________?
Show answer

Answer: B. 62.5 m

Using the kinematic formula s equals zero point five multiplied by acceleration and time squared. Multiplying zero point five by an acceleration of five and twenty five for time squared. Calculating this algebraic produc...

Q4. In accordance with the principle of moments__________________?

Select your answer for: In accordance with the principle of moments__________________?
Show answer

Answer: B. if a system of coplanar forces is in equilibrium, then the algebraic sum of their moments about any point in their plane is zero

The principle of moments states that for a coplanar force system in static equilibrium moments sum to zero. This fundamental rule applies to any arbitrary pivot point chosen within the same geometric plane of the forces....

Q5. A single applied force coupled with a moment acting within the same plane on a rigid body results in_____________________?

Select your answer for: A single applied force coupled with a moment acting within the same plane on a rigid body results in_____________________?
Show answer

Answer: B. cannot balance each other

A single applied force causes translational motion of a rigid body along its line of action. A pure moment or couple creates rotational motion around an axis without producing any net translation. Because force causes tr...

Q6. A concurrent system of forces acting at a point achieves static equilibrium when_____________________?

Select your answer for: A concurrent system of forces acting at a point achieves static equilibrium when_____________________?
Show answer

Answer: C. sum of resolved parts in any two per-pendicular directions are both zero

Concurrent force systems achieve static equilibrium when force components in perpendicular directions sum to zero. The algebraic sum of resolved force parts in any two orthogonal directions must equal zero. Balancing all...

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test