Skip to main content
Sarkari MCQs Government Exam Question Bank
Menu
Question no. 57035

A motor flywheel accelerates from a standstill to 1000 rpm over 6 seconds. Approximately how many complete revolutions does it execute___________________?

Select your answer for: A motor flywheel accelerates from a standstill to 1000 rpm over 6 seconds. Approximately how many complete revolutions does it execute___________________?
Show answer

Answer: B. 50

Explanation

Integrating angular velocity over the six-second acceleration period from rest to one thousand revolutions per minute yields a total displacement of approximately fifty complete revolutions. Assuming constant angular acceleration, the average speed during the six-second interval equals five hundred revolutions per minute. Multiplying this average speed of five hundred revolutions per minute by the time duration of zero point one minutes gives fifty revolutions. Rotational displacement is calculated by integrating the angular velocity function with respect to elapsed time. Angular velocity in revolutions per minute must be converted to revolutions per second for time integration calculations. Kinematic equations of motion assume uniform acceleration when calculating velocity and displacement profiles for rotating machinery.

A value of twenty-five revolutions underestimates the total displacement by half, ignoring the average speed calculation. Estimates of one hundred or two50 revolutions assume incorrect acceleration profiles or excessive time durations. Calculations resulting in five hundred revolutions fail to account for the zero-velocity starting condition of the flywheel.

Subject
Engineering
Topic
—
Difficulty
medium

Related questions

Q1. A mass W resting on an inclined plane is on the verge of being pulled upward by a horizontal pull P. This motion impends when P equates to________________?

Select your answer for: A mass W resting on an inclined plane is on the verge of being pulled upward by a horizontal pull P. This motion impends when P equates to________________?
Show answer

Answer: C. Wtan(a + <|))

The pulling force required to move a body up an inclined plane is determined by weight and friction angles. Resolving forces parallel and perpendicular to the inclined plane yields the exact static equilibrium equation....

Q2. Liquid water reaches its maximum density value at__________________?

Select your answer for: Liquid water reaches its maximum density value at__________________?
Show answer

Answer: C. 4°C

Liquid water exhibits anomalous thermal expansion behavior, contracting as it warms from melting point until reaching maximum density. The highest density value for pure liquid water occurs precisely at four degrees Cels...

Q3. The assertion that diesel engines exhibit lower specific fuel consumption than petrol engines is classified as____________________?

Select your answer for: The assertion that diesel engines exhibit lower specific fuel consumption than petrol engines is classified as____________________?
Show answer

Answer: D. true at both part and full load

Diesel engines maintain lower specific fuel consumption than petrol engines across all operating loads. Higher compression ratios and lean burning allow diesels to extract more energy per unit of fuel. This thermodynamic...

Q4. Thermal cycle efficiency is elevated by________________?

Select your answer for: Thermal cycle efficiency is elevated by________________?
Show answer

Answer: C. both A. and B.

Both steam regeneration and reheating improve the overall thermal efficiency of steam power cycles. Regeneration preheats boiler feed water using extracted steam to reduce external heat addition requirements. Reheating s...

Q5. What are the fundamental dimensional units of surface tension___________________?

Select your answer for: What are the fundamental dimensional units of surface tension___________________?
Show answer

Answer: A. MlL°T2

Surface tension is defined mathematically as force acting per unit length along the surface of a liquid. Force has dimensional units of mass multiplied by acceleration, expressed as M L T^-2 in fundamental dimensions. Di...

Q6. During a polytropic thermodynamic expansion or compression_________________?

Select your answer for: During a polytropic thermodynamic expansion or compression_________________?
Show answer

Answer: D. all of the above

Polytropic processes involve simultaneous heat transfer, mechanical work, and property state changes in gases. Working fluids can shift between wet, dry, or superheated states during polytropic expansion or compression....

New!

Mock Test System is now available!

Prepare for your exam with interactive mock tests. Select your subjects, attempt 100 random MCQs against the clock, and see exactly where you stand.

Start Mock Test